Linde Heliarc Manual

Linde Heliarc Manual

Linde Heliarc 250 Hf Manual
Linde Heliarc Manual Diagram
Get Free Linde Heliarc Manual Linde Heliarc Manual When somebody should go to the books stores, search launch by shop, shelf by shelf, it is in point of fact problematic. This is why we present the book compilations in this website. It will extremely ease you to look guide linde heliarc manual as you such as. I have an opportunity to purchase a well preserved LINDE HELIARC 250 HF. It is in great condition, comes with gas cylinder and regulator, water cooling tank, pump and foot controller. It is single phase 220-240 V and has a water cooled tig torch. LINDE HELIARC 250 HF TIG and Stick Welder.
This TIG foot control cross reference guide will help you determine which foot pedal can be used with your welder. To determine which control will work with your welder, check the number of pins on your welder's remote receptacle (and the shape of the connector) to make sure it matches one of the plugs below. You can also check to make sure the foot pedal's model number in your owner's manual matches a model number below.
Questions? Call us at 1-440-205-1600 or send an email. We can assist in finding the TIG welding foot pedal that you require.
Torrent securecrt for mac. You can also go to the TIG Welding Foot Pedals Home Page to order.
SSC Model NumberFoot Control DescriptionConnector (View of Plug End Face)Compatible With:
C810-1425TIG Foot Control Pedal for Miller® and Hobart® TIG welders. Replaces Miller RFCS-14 (p/n 043554), RFCS-14 HD (p/n 194744), and Hobart® p/n 043554.14 pin
Works with any Miller TIG welder equipped with a 14-pin remote receptacle for foot controls. For Miller solid-state power sources AFTER serial number JK674521.Miller Econotig, AeroWave, ALT 304, Big Blue 302, Big Blue 402, CST 250, CST 280, Dimension 302, Dimension 400, Dimension 452, Dimension 650, Dimension 652, Dimension 1000, Dynasty 200 SD and DX, Dynasty 210, Dynasty 280, Dynasty 300 SD and DX, Dynasty 350, Dynasty 400, Dynasty 700, Dynasty 800, Goldstar 300SS, Goldstar 400SS, Goldstar 500SS, Goldstar 600SS, Goldstar 302, Goldstar 452, Goldstar 652, Goldstar 402, Goldstar 602, Goldstar 852, HF-251-2, HF-251D-1, Maxstar 90, Maxstar 91, Maxstar 151, Maxstar 152, Maxstar 175, Maxstar 200, Maxstar 210, Maxstar 280, Maxstar 350, Maxstar 400, Maxstar 700, Maxstar 800, Maxtron 300, Maxtron 450, Metro 250D, MK VI, Multimatic 220 AC/DC, Multimatic 255, Phoenix 456, PipeWorx 400, ShopMaster 300, Shopmate 300 DX, SyncroWave 180, SyncroWave 200, SyncroWave 210, SyncroWave 250, SyncroWave 350 LX, SyncroWave 351, TIG Runner, Trailblazer 250G, Trailblazer 301G, Trailblazer 251NT, Trailblazer 300D NT, XMT 200, XMT 300, XMT 304, XMT 350, XMT 450, RFCS-14, RFCS-14 HD, 043554, 194744
For the Miller 330 Aircrafter, SyncroWave 300, SyncroWave 500: Double check the number of pins in the welder's remote receptacle for these welders, as they may use either the 14-pin or the 5-pin plug below.
Hobart: TigMate, Cybertig 180, Cybertig 250, Cybertig 350
Powcon: 300 TSE only, which has a metal connection with a blue plastic center. All other PowCon see the C880-1425 below.
Thermadyne / Thermal Arc 10-2007 and 10-2008
Sanrex 200AP
C810-0525TIG Foot Control Pedal for Miller® TIG welders with 5-pin remote control connection. Replaces Miller® RFCS-5 (p/n 043716), RFCS-5 HD (p/n 195218) and RFCS-23.5 pin
For Miller TIG welders equipped with a 5-pin remote receptacle. For Miller solid-state power sources BEFORE serial number JK674521.
Miller Maxstar 150 (Not 150S, Not 150 STR or STH), HF-250D-1, and HF-250-1, HF-250-2. Also works with the Synchrowave 300 (most Synchrowaves use the 14-pin model above), which called out the RFCS-23. If you have a different welder which wants the RFCS-23, please call before buying so that we can check your owner's manual to verify.
C810-0625TIG Foot Control Pedal for Miller® Maxstar 161 STL and STH and Multimatic 200. Replaces Miller® RFCS-6M (p/n 195183 or 195504).6 pin
Miller RFCS-6M (195183 or 195504): For Maxstar 150 STL, Maxstar STH, Maxstar 161 STL, Maxstar 161 STH, STi160, Multimatic 200 (when properly equipped), and Maxstar 140 STR with Lift-Arc TIG option (current control only).Hobart®: Hobart 150 STi
Does not work with Maxstar 140, which has no receptacle.
C810-0814TIG Foot Control Pedal for Miller® Diversion 165, Diversion 180, and Hobart® EZ-TIG 165. Replaces Miller® RFCS-RJ45 (p/n 300432) and Hobart p/n 245589.8 pin RJ-45 Plug
Miller RFCS-RJ45 (300432): For Diversion 165 or Diversion 180. Hobart (245589): EZ-TIG 165i. Miller Multimatic 215 (when properly equipped with TIG contractor kit).Note: This model is our standard steel full-sized platform with million-cycle rating, including our standard industrial-quality potentiometer, steel case, and full-sized foot platform, not the light-duty components used by Miller® for their Diversion foot control. See picture comparison: click to view image.
C820-0625TIG Foot Control Pedal for 6-Pin Lincoln® TIG Welders (replaces K870)6 pinLincoln Precision Tig 225, 275, 375; Square Wave 175, 175 Pro, 185; Tig 200, 255, 275, 300, 350, 355; Tig 250/250, Tig 300/300 (with Code higher than 8875); Invertec V160T, V160S, V205T, V250T, V275S, V300 Pro, V350 Pro; DC400, DC600, DC655; Aspect 375; 210 MP (for TIG-ready models); and more (if equipped for TIG welding with the 6-pin remote output receptacle on the welder)
C840-0725TIG Foot Control for Cigweld®7-pin
Cigweld Transtig 150, Transarc 275, and others. Replaces Cigweld p/n 646321. See picture of actual plug here: plug image. This will only work with receptacles that fit the pin layout shown.
C850-0825TIG Foot Control for Thermal Arc® / ESAB / Victor welders. Replaces 10-4016, 10-4015, and 600285.8 pin
Thermal Arc / ESAB: For replacement of Thermal Arc foot controls 10-4016, 10-4015, and 600285.CigWeld: W4015800 for the Weldskill 200 AC/DC. Firepower: 1442-0025.
This will not replace the ESAB W4014450 or W4013200. See below for those models. Coconut battery for mac.
C850-0815XTIG Foot Control for ESAB® welders.8 pin
ESAB Rebel Series (Rebel EMP 205ic AC/DC, EMP 215ic, EMP 235ic, and EMP 285ic TIG welders) and MINIARC ROGUE ES 180I. Replaces foot pedal p/n W4014450.
C850-0815XSTIG Foot Control for ESAB® welders.8 pin
Thermal Arc 186 or ESAB ET 186i AC/DC welders. Replaces foot pedal p/n W4013200. Note: This model is only for the welders listed (has extra switch in the pedal).
C860-1430TIG Foot Control for ESAB® TIG welders. Replaces ESAB® model FC-5B (p/n 33646) and FC-5C (p/n 0558004234).14 pinESAB Miniarc 90i and 140i, Heliarc 252, Heliarc 352, Heliarc 582cc, Heliarc 453cc-553cc, Multimaster 260, Heliarc 160i, Miniarc 140i, Digipulse, Aristo 350 mpi, etc.
C860-0625TIG Foot Control for ESAB®, Airco®, and Linde® TIG welders. Replaces model FC-4 (p/n 13880043) or FC 004.6 pin
ESAB / Airco Heliwelder. For models with the 6-pin rectangular connector. Note: This is not the same as the 2-plug version of the FC-4 (listed below). Check the plug configuration of your welder.
C870-0625TIG Foot Control for Hobart® or L-TEC® welders with 6-pin connector. Replaces Hobart foot control model 409213A.6 pinHobart MegaArc with 6-pin connector.L-TEC MigMaster with TIG option and 6-pin.
C870-1025TIG Foot Control for older Hobart® TIG welders. Replaces Hobart® models 409004A, 362668, and 200460-001.10 pin
Hobart: CyberTig; CT-200, CT-300, Cyberwave 300-S, Tigwave 250, Tigwave 350, TR250-HF, and other Hobart welders that fit the 10-pin connector shown. Also works on Panasonic Multi 260 welders if they have the 10-pin receptacle shown.
C870-1225TIG Foot Control for 12-pin Airco® Heliwelder 251 AC/DC.12 pin
Airco Heliwelder 251 AC/DC. Has 12-pin Souriau connector (p/n UTG61412PN) with pin terminals and 25,000-ohm potentiometer. Uses pins D, E, F, G, and H. See picture of 12-pin plug here.
C870-1925TIG Foot Control for 19-pin older welders (Hobart or ThermaDyne).19 pin
Foot Control for Hobart or ThermaDyne welders using a 19-pin connector. Replaces models 409004A-2 and THL 200460-007. Only pins A, B, K, J, and H are connected.Note: This model may be difficult to match and is rare. Be sure part number and plug are correct. The receptacle on your machine must exactly match the plug as shown. See image of plug here (receptacle on machine will have reverse lettering).
C880-1425TIG Foot Control for 14-pin Powcon® TIG welders.14 pin
Powcon: Replaces remote TIG controls for Powcon power sources using a 14-pin Amp® twist-lock black plastic connector.
C885-1425TIG Foot Control for 14-pin Lorch welders (replaces Lorch FR-35).n/aLorch: Replaces Lorch FR-35. Includes 25-foot cable and 14-pin plug, 100,000-ohm potentiometer, switch.
C890-0625TIG Foot Control for Linde® UCC-305 welder. Replaces Linde® FC-4 p/n 679662.3 pin/3 pin (two plugs)
click for picture
Linde: UCC-305 and similar machines (uses two Hubbell® Twist-Lock plugs).L-TEC / Linde: Heliarc 250 HF.
Check the plug configuration of your welder. It must match the picture shown to the left for this foot pedal to work with the welder.
Note: This is not the same as the 6-pin version of the FC-4 (listed above).
C910-0725TIG Foot Control for AHP and Primeweld 7-pin welders7-pinFor AHP and Primeweld welders using a 7-pin pedal including AHP AlphaTIG 201XD, AHP AlphaTIG 200x, and Primeweld TIG225X ACDC, 
C925-0725TIG Foot Control for Everlast welders using 22.5K or 25K pedals7-pinFor all Everlast TIG welders that work with a 22.5 or 25K ohm pedal with a 7-pin plug including: PowerArc 160iSTH, PowerArc 161STH, PowerArc 210STL, PowerArc 280STH, Poweri-TIG 201, Poweri-TIG 200T, PowerTIG 185DV, PowerTIG 200DV, PowerTIG 210EXT, PowerTIG 250EX, PowerTIG 255EXT, PowerTIG 315LX, PowerTIG 325EXT, PowerTIG 350EXT, SuperUltra 206Si, PowerUltra 206Pi, PowerPro 164Si, PowerPro 205Si, PowerPro 256Si, PowerPro 256DNot designed to replace or fit units with amp control knob on pedal, or units that do not limit maximum amps on panel while foot pedal is in use. NOT for MTS use.
C950-0725TIG Foot Control for Everlast welders using 47K or 50K pedals7-pinFor Everlast TIG welders that work with a 47K or 50K ohm pedal with a 7-pin plug. NOT for MTS use.
5-pinPOWERCRAFT TIG 201 AC/DCWe are working on obtaining the information on the 5-pin plug. If you are interested in this pedal, please let us know.

SSC Model Number	Foot Control Description	Connector (View of Plug End Face)	Compatible With:
C810-1425	TIG Foot Control Pedal for Miller® and Hobart® TIG welders. Replaces Miller RFCS-14 (p/n 043554), RFCS-14 HD (p/n 194744), and Hobart® p/n 043554.	14 pin	Works with any Miller TIG welder equipped with a 14-pin remote receptacle for foot controls. For Miller solid-state power sources AFTER serial number JK674521. Miller Econotig, AeroWave, ALT 304, Big Blue 302, Big Blue 402, CST 250, CST 280, Dimension 302, Dimension 400, Dimension 452, Dimension 650, Dimension 652, Dimension 1000, Dynasty 200 SD and DX, Dynasty 210, Dynasty 280, Dynasty 300 SD and DX, Dynasty 350, Dynasty 400, Dynasty 700, Dynasty 800, Goldstar 300SS, Goldstar 400SS, Goldstar 500SS, Goldstar 600SS, Goldstar 302, Goldstar 452, Goldstar 652, Goldstar 402, Goldstar 602, Goldstar 852, HF-251-2, HF-251D-1, Maxstar 90, Maxstar 91, Maxstar 151, Maxstar 152, Maxstar 175, Maxstar 200, Maxstar 210, Maxstar 280, Maxstar 350, Maxstar 400, Maxstar 700, Maxstar 800, Maxtron 300, Maxtron 450, Metro 250D, MK VI, Multimatic 220 AC/DC, Multimatic 255, Phoenix 456, PipeWorx 400, ShopMaster 300, Shopmate 300 DX, SyncroWave 180, SyncroWave 200, SyncroWave 210, SyncroWave 250, SyncroWave 350 LX, SyncroWave 351, TIG Runner, Trailblazer 250G, Trailblazer 301G, Trailblazer 251NT, Trailblazer 300D NT, XMT 200, XMT 300, XMT 304, XMT 350, XMT 450, RFCS-14, RFCS-14 HD, 043554, 194744 For the Miller 330 Aircrafter, SyncroWave 300, SyncroWave 500: Double check the number of pins in the welder's remote receptacle for these welders, as they may use either the 14-pin or the 5-pin plug below. Hobart: TigMate, Cybertig 180, Cybertig 250, Cybertig 350 Powcon: 300 TSE only, which has a metal connection with a blue plastic center. All other PowCon see the C880-1425 below. Thermadyne / Thermal Arc 10-2007 and 10-2008 Sanrex 200AP
C810-0525	TIG Foot Control Pedal for Miller® TIG welders with 5-pin remote control connection. Replaces Miller® RFCS-5 (p/n 043716), RFCS-5 HD (p/n 195218) and RFCS-23.	5 pin	For Miller TIG welders equipped with a 5-pin remote receptacle. For Miller solid-state power sources BEFORE serial number JK674521. Miller Maxstar 150 (Not 150S, Not 150 STR or STH), HF-250D-1, and HF-250-1, HF-250-2. Also works with the Synchrowave 300 (most Synchrowaves use the 14-pin model above), which called out the RFCS-23. If you have a different welder which wants the RFCS-23, please call before buying so that we can check your owner's manual to verify.
C810-0625	TIG Foot Control Pedal for Miller® Maxstar 161 STL and STH and Multimatic 200. Replaces Miller® RFCS-6M (p/n 195183 or 195504).	6 pin	Miller RFCS-6M (195183 or 195504): For Maxstar 150 STL, Maxstar STH, Maxstar 161 STL, Maxstar 161 STH, STi160, Multimatic 200 (when properly equipped), and Maxstar 140 STR with Lift-Arc TIG option (current control only). Hobart®: Hobart 150 STi Does not work with Maxstar 140, which has no receptacle.
C810-0814	TIG Foot Control Pedal for Miller® Diversion 165, Diversion 180, and Hobart® EZ-TIG 165. Replaces Miller® RFCS-RJ45 (p/n 300432) and Hobart p/n 245589.	8 pin RJ-45 Plug	Miller RFCS-RJ45 (300432): For Diversion 165 or Diversion 180. Hobart (245589): EZ-TIG 165i. Miller Multimatic 215 (when properly equipped with TIG contractor kit). Note: This model is our standard steel full-sized platform with million-cycle rating, including our standard industrial-quality potentiometer, steel case, and full-sized foot platform, not the light-duty components used by Miller® for their Diversion foot control. See picture comparison: click to view image.
C820-0625	TIG Foot Control Pedal for 6-Pin Lincoln® TIG Welders (replaces K870)	6 pin	Lincoln Precision Tig 225, 275, 375; Square Wave 175, 175 Pro, 185; Tig 200, 255, 275, 300, 350, 355; Tig 250/250, Tig 300/300 (with Code higher than 8875); Invertec V160T, V160S, V205T, V250T, V275S, V300 Pro, V350 Pro; DC400, DC600, DC655; Aspect 375; 210 MP (for TIG-ready models); and more (if equipped for TIG welding with the 6-pin remote output receptacle on the welder)
C840-0725	TIG Foot Control for Cigweld®	7-pin	Cigweld Transtig 150, Transarc 275, and others. Replaces Cigweld p/n 646321. See picture of actual plug here: plug image. This will only work with receptacles that fit the pin layout shown.
C850-0825	TIG Foot Control for Thermal Arc® / ESAB / Victor welders. Replaces 10-4016, 10-4015, and 600285.	8 pin	Thermal Arc / ESAB: For replacement of Thermal Arc foot controls 10-4016, 10-4015, and 600285. CigWeld: W4015800 for the Weldskill 200 AC/DC. Firepower: 1442-0025. This will not replace the ESAB W4014450 or W4013200. See below for those models. Coconut battery for mac.
C850-0815X	TIG Foot Control for ESAB® welders.	8 pin	ESAB Rebel Series (Rebel EMP 205ic AC/DC, EMP 215ic, EMP 235ic, and EMP 285ic TIG welders) and MINIARC ROGUE ES 180I. Replaces foot pedal p/n W4014450.
C850-0815XS	TIG Foot Control for ESAB® welders.	8 pin	Thermal Arc 186 or ESAB ET 186i AC/DC welders. Replaces foot pedal p/n W4013200. Note: This model is only for the welders listed (has extra switch in the pedal).
C860-1430	TIG Foot Control for ESAB® TIG welders. Replaces ESAB® model FC-5B (p/n 33646) and FC-5C (p/n 0558004234).	14 pin	ESAB Miniarc 90i and 140i, Heliarc 252, Heliarc 352, Heliarc 582cc, Heliarc 453cc-553cc, Multimaster 260, Heliarc 160i, Miniarc 140i, Digipulse, Aristo 350 mpi, etc.
C860-0625	TIG Foot Control for ESAB®, Airco®, and Linde® TIG welders. Replaces model FC-4 (p/n 13880043) or FC 004.	6 pin	ESAB / Airco Heliwelder. For models with the 6-pin rectangular connector. Note: This is not the same as the 2-plug version of the FC-4 (listed below). Check the plug configuration of your welder.
C870-0625	TIG Foot Control for Hobart® or L-TEC® welders with 6-pin connector. Replaces Hobart foot control model 409213A.	6 pin	Hobart MegaArc with 6-pin connector. L-TEC MigMaster with TIG option and 6-pin.
C870-1025	TIG Foot Control for older Hobart® TIG welders. Replaces Hobart® models 409004A, 362668, and 200460-001.	10 pin	Hobart: CyberTig; CT-200, CT-300, Cyberwave 300-S, Tigwave 250, Tigwave 350, TR250-HF, and other Hobart welders that fit the 10-pin connector shown. Also works on Panasonic Multi 260 welders if they have the 10-pin receptacle shown.
C870-1225	TIG Foot Control for 12-pin Airco® Heliwelder 251 AC/DC.	12 pin	Airco Heliwelder 251 AC/DC. Has 12-pin Souriau connector (p/n UTG61412PN) with pin terminals and 25,000-ohm potentiometer. Uses pins D, E, F, G, and H. See picture of 12-pin plug here.
C870-1925	TIG Foot Control for 19-pin older welders (Hobart or ThermaDyne).	19 pin	Foot Control for Hobart or ThermaDyne welders using a 19-pin connector. Replaces models 409004A-2 and THL 200460-007. Only pins A, B, K, J, and H are connected. Note: This model may be difficult to match and is rare. Be sure part number and plug are correct. The receptacle on your machine must exactly match the plug as shown. See image of plug here (receptacle on machine will have reverse lettering).
C880-1425	TIG Foot Control for 14-pin Powcon® TIG welders.	14 pin	Powcon: Replaces remote TIG controls for Powcon power sources using a 14-pin Amp® twist-lock black plastic connector.
C885-1425	TIG Foot Control for 14-pin Lorch welders (replaces Lorch FR-35).	n/a	Lorch: Replaces Lorch FR-35. Includes 25-foot cable and 14-pin plug, 100,000-ohm potentiometer, switch.
C890-0625	TIG Foot Control for Linde® UCC-305 welder. Replaces Linde® FC-4 p/n 679662.	3 pin/3 pin (two plugs) click for picture	Linde: UCC-305 and similar machines (uses two Hubbell® Twist-Lock plugs). L-TEC / Linde: Heliarc 250 HF. Check the plug configuration of your welder. It must match the picture shown to the left for this foot pedal to work with the welder. Note: This is not the same as the 6-pin version of the FC-4 (listed above).
C910-0725	TIG Foot Control for AHP and Primeweld 7-pin welders	7-pin	For AHP and Primeweld welders using a 7-pin pedal including AHP AlphaTIG 201XD, AHP AlphaTIG 200x, and Primeweld TIG225X ACDC,
C925-0725	TIG Foot Control for Everlast welders using 22.5K or 25K pedals	7-pin	For all Everlast TIG welders that work with a 22.5 or 25K ohm pedal with a 7-pin plug including: PowerArc 160iSTH, PowerArc 161STH, PowerArc 210STL, PowerArc 280STH, Poweri-TIG 201, Poweri-TIG 200T, PowerTIG 185DV, PowerTIG 200DV, PowerTIG 210EXT, PowerTIG 250EX, PowerTIG 255EXT, PowerTIG 315LX, PowerTIG 325EXT, PowerTIG 350EXT, SuperUltra 206Si, PowerUltra 206Pi, PowerPro 164Si, PowerPro 205Si, PowerPro 256Si, PowerPro 256D Not designed to replace or fit units with amp control knob on pedal, or units that do not limit maximum amps on panel while foot pedal is in use. NOT for MTS use.
C950-0725	TIG Foot Control for Everlast welders using 47K or 50K pedals	7-pin	For Everlast TIG welders that work with a 47K or 50K ohm pedal with a 7-pin plug. NOT for MTS use.
5-pin	POWERCRAFT TIG 201 AC/DC We are working on obtaining the information on the 5-pin plug. If you are interested in this pedal, please let us know.

Linde Heliarc 250 Hf ManualModels that use high-power rheostats or have other issues that are not compatible with the SSC design.
Foot Control Description or Manufacturer's ModelConnectorUsed With:
Miller RFC-23A3 pin/2 pin (two twistlock plugs)Miller®: Dialarc 250 AC/DC, Dialarc HF, Gold Star 330 A/BP and 320 A/BPSSC does not make a pedal that replaces the RFC-23A, which uses a 15-ohm, 130-watt rheostat. Our design, like that of most welding pedals made today, uses a 2-watt, high-resolution rotary potentiometer for the weld current control. We suggest buying the RFC-23A from your local Miller distributor. Do not confuse it with the RFCS-23, RFC-23AG, or RFC-23GD25A, all of which are different models and use 130W or 300W rheostats of different resistance values (see the Miller website for info about different models). You can sometimes find these used on eBay, but remember to research with the seller to make sure the pedal works for your welder. Miller also sells some welder parts you can find through internet searches (such as Miller rheostat part number 175264) if you need repair parts.
Eutectic4-prong twistlockEutectic FC-2 uses a 20-ohm wirewound rheostat and a single cable with a 4-prong twistlock plug. Wattage is unknown.
Pedals for Hobart TG201 and TG3015-pinHobart models TG-201 and TG-301 use a 25-watt, 250-ohm rheostat and the MS3106A18-20P Amphenol 5-pin plug. This is not the same plug that is used on the standard Miller 5-pin amptrol foot pedal (C810-0525).
Note: The wattage is the maximum power that a potentiometer or rheostat can handle (a rheostat is a high-power potentiometer). In the 1960s and 1970s, welding manufacturers used higher-wattage rheostats ranging from 25 to 300 watts, depending on the model, but they changed to the safer circuitry associated with the 2-watt potentiometer in the 1980s and have used this style since that time. The SSC Controls foot pedals use a 2-watt potentiometer and cannot fit the high-power rheostats, so we cannot make these models.
Other models that we cannot make:ESAB Migmaster 300i -- Requires foot control part number 33517. We cannot make this model.
ESAB Caddy TIG -- Requires foot pedal T1 CAN. This has a PC board inside the foot control that is installed in Europe. We cannot make this model.
ESAB FS002 -- Has two plugs and two pots inside the foot control. We cannot make this model.
ESAB ER 1F Foot Control (0445550881) -- We cannot make this model.
Airco 150 AC/DC Heliwelder -- Has one 3-pronged plug. Uses large rheostat. We cannot make this model.
Fronius 4046090 (TR 2200-FM) Foot Pedal -- Has a PC board inside the foot pedal. We cannot make this model.
Any model with a knob on the side of the foot pedal. We cannot make this type of control.
We cannot make a foot pedal for any Eastwood welder that has a knob on the side of the foot pedal.

Foot Control Description or Manufacturer's Model	Connector	Used With:
Miller RFC-23A	3 pin/2 pin (two twistlock plugs)	Miller®: Dialarc 250 AC/DC, Dialarc HF, Gold Star 330 A/BP and 320 A/BP SSC does not make a pedal that replaces the RFC-23A, which uses a 15-ohm, 130-watt rheostat. Our design, like that of most welding pedals made today, uses a 2-watt, high-resolution rotary potentiometer for the weld current control. We suggest buying the RFC-23A from your local Miller distributor. Do not confuse it with the RFCS-23, RFC-23AG, or RFC-23GD25A, all of which are different models and use 130W or 300W rheostats of different resistance values (see the Miller website for info about different models). You can sometimes find these used on eBay, but remember to research with the seller to make sure the pedal works for your welder. Miller also sells some welder parts you can find through internet searches (such as Miller rheostat part number 175264) if you need repair parts.
Eutectic	4-prong twistlock	Eutectic FC-2 uses a 20-ohm wirewound rheostat and a single cable with a 4-prong twistlock plug. Wattage is unknown.
Pedals for Hobart TG201 and TG301	5-pin	Hobart models TG-201 and TG-301 use a 25-watt, 250-ohm rheostat and the MS3106A18-20P Amphenol 5-pin plug. This is not the same plug that is used on the standard Miller 5-pin amptrol foot pedal (C810-0525).
Note: The wattage is the maximum power that a potentiometer or rheostat can handle (a rheostat is a high-power potentiometer). In the 1960s and 1970s, welding manufacturers used higher-wattage rheostats ranging from 25 to 300 watts, depending on the model, but they changed to the safer circuitry associated with the 2-watt potentiometer in the 1980s and have used this style since that time. The SSC Controls foot pedals use a 2-watt potentiometer and cannot fit the high-power rheostats, so we cannot make these models.
Other models that we cannot make: ESAB Migmaster 300i -- Requires foot control part number 33517. We cannot make this model. ESAB Caddy TIG -- Requires foot pedal T1 CAN. This has a PC board inside the foot control that is installed in Europe. We cannot make this model. ESAB FS002 -- Has two plugs and two pots inside the foot control. We cannot make this model. ESAB ER 1F Foot Control (0445550881) -- We cannot make this model. Airco 150 AC/DC Heliwelder -- Has one 3-pronged plug. Uses large rheostat. We cannot make this model. Fronius 4046090 (TR 2200-FM) Foot Pedal -- Has a PC board inside the foot pedal. We cannot make this model. Any model with a knob on the side of the foot pedal. We cannot make this type of control. We cannot make a foot pedal for any Eastwood welder that has a knob on the side of the foot pedal.

Linde Heliarc 250 Hf ManualModels that use high-power rheostats or have other issues that are not compatible with the SSC design.
Foot Control Description or Manufacturer's ModelConnectorUsed With:
Miller RFC-23A3 pin/2 pin (two twistlock plugs)Miller®: Dialarc 250 AC/DC, Dialarc HF, Gold Star 330 A/BP and 320 A/BPSSC does not make a pedal that replaces the RFC-23A, which uses a 15-ohm, 130-watt rheostat. Our design, like that of most welding pedals made today, uses a 2-watt, high-resolution rotary potentiometer for the weld current control. We suggest buying the RFC-23A from your local Miller distributor. Do not confuse it with the RFCS-23, RFC-23AG, or RFC-23GD25A, all of which are different models and use 130W or 300W rheostats of different resistance values (see the Miller website for info about different models). You can sometimes find these used on eBay, but remember to research with the seller to make sure the pedal works for your welder. Miller also sells some welder parts you can find through internet searches (such as Miller rheostat part number 175264) if you need repair parts.
Eutectic4-prong twistlockEutectic FC-2 uses a 20-ohm wirewound rheostat and a single cable with a 4-prong twistlock plug. Wattage is unknown.
Pedals for Hobart TG201 and TG3015-pinHobart models TG-201 and TG-301 use a 25-watt, 250-ohm rheostat and the MS3106A18-20P Amphenol 5-pin plug. This is not the same plug that is used on the standard Miller 5-pin amptrol foot pedal (C810-0525).
Note: The wattage is the maximum power that a potentiometer or rheostat can handle (a rheostat is a high-power potentiometer). In the 1960s and 1970s, welding manufacturers used higher-wattage rheostats ranging from 25 to 300 watts, depending on the model, but they changed to the safer circuitry associated with the 2-watt potentiometer in the 1980s and have used this style since that time. The SSC Controls foot pedals use a 2-watt potentiometer and cannot fit the high-power rheostats, so we cannot make these models.
Other models that we cannot make:ESAB Migmaster 300i -- Requires foot control part number 33517. We cannot make this model.
ESAB Caddy TIG -- Requires foot pedal T1 CAN. This has a PC board inside the foot control that is installed in Europe. We cannot make this model.
ESAB FS002 -- Has two plugs and two pots inside the foot control. We cannot make this model.
ESAB ER 1F Foot Control (0445550881) -- We cannot make this model.
Airco 150 AC/DC Heliwelder -- Has one 3-pronged plug. Uses large rheostat. We cannot make this model.
Fronius 4046090 (TR 2200-FM) Foot Pedal -- Has a PC board inside the foot pedal. We cannot make this model.
Any model with a knob on the side of the foot pedal. We cannot make this type of control.
We cannot make a foot pedal for any Eastwood welder that has a knob on the side of the foot pedal.
Linde Heliarc Manual DiagramMiller® and Hobart® are registered trademarks of the Miller Electric Mfg Co. ESAB® is a registered trademark of the ESAB Group, Inc. Thermal Arc® is a registered trademark of the Thermadyne Holdings Corporation.